Rheem Heat Pump Installation Nationwide | Dalton Heating & Air Alpharetta

Rheem Heat Pump Installation in Alpharetta: What to Know First

Rheem heat pump installation in Alpharetta typically runs $3,500 – $7,500 depending on the model line, your home’s square footage, and whether existing ductwork can stay. Most installations take one full day, sometimes two if we’re replacing aged duct transitions or reworking the pad. We give you a written price before any work starts, so you know the exact number before the first wrench turns.

Call (229) 537-2086

This page is for Alpharetta homeowners who own a Rheem or are considering one, and want to know what installation actually involves, what it costs, and what goes wrong when it’s done poorly. Call (229) 537-2086 for a free estimate. We’re an independent Rheem service provider, not a factory arm, which means we answer to you, not a corporate quota.

How Rheem Products Fail – and How We Fix Them

Rheem builds solid equipment, but every brand has its known weak points. Here’s what we see on heat pump installs in Alpharetta and how we handle each one.

• Reversing valve sticking on older RP14 and RP15 units. The reversing valve is what lets a heat pump switch between cooling and heating. On Rheem units that are 8-12 years old, the solenoid can stick, leaving the system stuck in one mode. During installation, we test the valve under load before tying in new line sets. If it’s marginal, we replace it at install rather than letting it fail in January when you need heat.
• Defrost board failures on Rheem Prestige series. The Prestige line runs a demand-defrost board that cycles the system to clear ice off the outdoor coil. Alpharetta’s humidity mixed with winter nights in the 30s means defrost cycles run often. A board that’s seen moisture intrusion will throw false defrost codes. We inspect the board, check for condensation inside the panel, and seal the enclosure properly before commissioning.
• Compressor start capacitor weak on RP17 units from the 2014-2018 era. These units shipped with a capacitor that degrades faster in Georgia heat. It’s not a Rheem defect exactly, it’s climate stress. On any RP17 install where the compressor has more than five years on it, we test the capacitor’s microfarad rating. If it’s below spec, a $40 part saves you a $1,200 compressor later.
• Line set sizing wrong on original installs in Alpharetta’s 1990s neighborhoods. Homes around Windward and Kimball Bridge were built fast in the 90s, and a lot of original heat pump line sets are undersized for modern R-410A Rheem equipment. We measure line length and diameter against the manufacturer’s chart for the specific model. Undersized lines restrict refrigerant flow and cut efficiency. We replace lines when the chart says they don’t meet spec.
• Condensate drain routing that can’t keep up with Georgia humidity. A heat pump in cooling mode pulls gallons of water out of Alpharetta air every day in summer. The emergency drain pan on many existing installs is too small or drains to a spot that promotes algae. We route primary and secondary drains so water moves away from the foundation, and we pitch the drain line correctly so standing water doesn’t grow mold in the attic.

Our Rheem Heat Pump Installation Process

Here’s how a Rheem heat pump installation with us actually goes, from first call to cleanup:

1. 1
   Call and schedule. A live person answers 24/7. We set a window, not a vague “sometime Tuesday.”
2. 2
   Site walk and load calculation. We measure conditioned square footage, window orientation, insulation levels, and existing duct condition. We don’t guess size from the old unit’s label. A Manual J calculation tells us what your house actually needs.
3. 3
   Written quote. You get the price in writing before any work starts. It includes equipment, materials, labor, permits, and disposal. No add-ons at the door.
4. 4
   Install day. We pull the old unit, inspect the pad, verify line set condition, and set the new Rheem unit. We pull a proper vacuum on the lines before charging the system. No shortcut evacuations.
5. 5
   Commissioning and test. We run the unit in both heating and cooling modes, check refrigerant pressures and temperature splits, and verify defrost operation. We walk you through the thermostat settings and filter locations.
6. 6
   Cleanup and paperwork. We haul off the old equipment, sweep the work area, and hand you the written 365-Day Done Right Promise. If anything’s not right for a full year, we fix it at no charge.

What Rheem Heat Pump Installation Costs in Alpharetta

Rheem heat pump installation in Alpharetta runs from roughly $3,500 for a base single-stage unit to $7,500 for a higher-efficiency two-stage or variable-speed model with more complex duct transitions. Most homes land between $4,500 and $6,000.

• Base single-stage Rheem (RP14, RP15): $3,500 – $4,800
• Two-stage Rheem Prestige (RP17): $5,200 – $6,500
• Variable-speed Rheem Prestige (RP20): $6,300 – $7,500

What moves the price: line set replacement, duct modifications, the condition of your electrical panel, and whether you need a new thermostat or plenum. We give you a free estimate with exact numbers before anything gets ordered. Call (229) 537-2086 and we’ll come out and price your job properly.

Why Alpharetta Homeowners Call Dalton Heating & Air Alpharetta for Rheem Work

Marco Benitez has been working on Rheem systems in Alpharetta homes for years, including the neighborhoods around Windward where undersized units and original line sets are common. He’ll walk you through exactly what failed and why before quoting a single dollar. That’s just how the crew works.

Every job gets a written price before work starts. Every repair carries a written guarantee for a full year. If the repair fails during that year, we come back at no charge. That’s the Garrison Standard, and it’s been in place since 2003. Our technicians are background-checked, uniformed, and factory-trained across nine major brands. If your Rheem install turns up a Carrier, Trane, or Lennox unit elsewhere in the house, we service those too.

FAQs